smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST3250310AS Serial Number: 6RYGGGJ1 Firmware Version: 4.AAA User Capacity: 250,059,350,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Sep 9 11:33:40 2009 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 64) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 253 006 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 142 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 064 060 030 Pre-fail Always - 2911405 9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1431 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 174 187 Unknown_Attribute 0x0032 001 001 000 Old_age Always - 126 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Temperature_Celsius 0x0022 059 059 045 Old_age Always - 689307689 194 Temperature_Celsius 0x0022 041 041 000 Old_age Always - 41 (Lifetime Min/Max 0/22) 195 Hardware_ECC_Recovered 0x001a 077 067 000 Old_age Always - 3046 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 3 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 3 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 126 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 126 occurred at disk power-on lifetime: 1431 hours (59 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 bd b2 9f e2 Error: UNC at LBA = 0x029fb2bd = 44020413 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 bd b2 9f e2 00 00:19:54.395 READ DMA 27 00 00 00 00 00 e0 00 00:20:02.710 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 02 00:20:02.710 IDENTIFY DEVICE ef 03 46 00 00 00 a0 02 00:20:02.688 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 00:20:02.677 READ NATIVE MAX ADDRESS EXT Error 125 occurred at disk power-on lifetime: 1431 hours (59 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 bd b2 9f e2 Error: UNC at LBA = 0x029fb2bd = 44020413 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 bd b2 9f e2 00 00:19:54.395 READ DMA 27 00 00 00 00 00 e0 00 00:19:54.382 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 02 00:19:54.381 IDENTIFY DEVICE ef 03 46 00 00 00 a0 02 00:19:54.374 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 00:19:50.308 READ NATIVE MAX ADDRESS EXT Error 124 occurred at disk power-on lifetime: 1431 hours (59 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 bd b2 9f e2 Error: UNC at LBA = 0x029fb2bd = 44020413 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 bd b2 9f e2 00 00:19:54.395 READ DMA 27 00 00 00 00 00 e0 00 00:19:54.382 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 02 00:19:54.381 IDENTIFY DEVICE ef 03 46 00 00 00 a0 02 00:19:54.374 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 00:19:50.308 READ NATIVE MAX ADDRESS EXT Error 123 occurred at disk power-on lifetime: 1431 hours (59 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 bd b2 9f e2 Error: UNC at LBA = 0x029fb2bd = 44020413 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 bd b2 9f e2 00 00:19:46.161 READ DMA 27 00 00 00 00 00 e0 00 00:19:42.074 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 02 00:19:42.035 IDENTIFY DEVICE ef 03 46 00 00 00 a0 02 00:19:42.015 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 00:19:50.308 READ NATIVE MAX ADDRESS EXT Error 122 occurred at disk power-on lifetime: 1431 hours (59 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 bd b2 9f e2 Error: UNC at LBA = 0x029fb2bd = 44020413 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 bd b2 9f e2 00 00:19:46.161 READ DMA 27 00 00 00 00 00 e0 00 00:19:42.074 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 02 00:19:42.035 IDENTIFY DEVICE ef 03 46 00 00 00 a0 02 00:19:42.015 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 00:19:41.995 READ NATIVE MAX ADDRESS EXT SMART Self-test log structure revision number 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.